Skip to main content

Aire One Barrie

Sealing Leaky Ducts in Belle Ewart: Where the Heat Goes

Round metal ductwork running across a ceiling, the runs that need sealing leaky ducts
17
November

Round metal ductwork running across a ceiling, the runs that need sealing leaky ducts
Belle Ewart · Homeowner guide

Air that escapes in the basement never reaches your bedroom.

Duct leaks are cheap to close and easy to find. The catch is that the wrong tape fails inside two winters, and sealing alone will not balance a system.

25%Of heat loss is leakage
R-12Minimum duct wrap
24/7Emergency service

5.0

Google rating from 131 reviews, as of November 17, 2026

Carrier Factory Authorized Dealer logo Technical Standards and Safety Authority logo HomeStars badge Aire One 30th anniversary badge Licensed technicians

Quick answer

Sealing leaky ducts closes the joints where heated air escapes before it reaches a room. Natural Resources Canada tells homeowners to seal plenums and both supply and return ducts with aluminium foil duct tape, approved flexible plastic tape or water based mastic. Above all, it warns against vinyl duct tape, which is the roll most people reach for first.

Key takeaways

  • Firstly, the common grey cloth tape is the wrong product here.
  • Return ducts leak as much as supply ducts, and get ignored.
  • Ducts in cold basements and crawl spaces should also be insulated.
  • Air leakage can account for roughly a quarter of a home’s heat loss.
  • Above all, sealing is not the same as balancing, and neither is cleaning.

Why duct leaks cost more than they look

First, the scale of it. Air leakage is not a minor line item in a Canadian house.

Natural Resources Canada puts the general figure bluntly: “typically about 25 percent of heat loss can be due to excess air infiltration (leakage).”

In practice, ducts contribute to that in a particular way. Heated air escaping into a cold basement is paid for and then wasted.

Meanwhile the return side pulls in the opposite direction. A leaking return draws cold basement air into the system, so the furnace works to reheat air it never meant to collect.

Consequently both halves matter. The federal guidance names them together, telling homeowners to “seal all plenums and supply and return ducts.”

Rectangular duct stencilled with the word supply above a ceiling
Supply and return both leak, and both need sealing.

The tape question, settled

Secondly, materials. This is where most weekend attempts go wrong.

In short, the approved list is a narrow one. Natural Resources Canada names “aluminum foil duct tape” along with “approved flexible plastic tape or water-based mastic.”

Then comes the warning. The same guidance says plainly: “do not use vinyl type duct tape.”

That matters because the grey cloth roll sold as duct tape is exactly the product meant. Its adhesive dries out in a warm, dusty duct and the tape peels within a season or two.

By contrast, mastic behaves differently. It is brushed on, it fills irregular gaps, and it stays flexible as the metal expands and contracts.

So the choice is simple in practice. Foil tape for clean, flat seams, and mastic where the joint is awkward.

Where to look for leaks

Thirdly, location. Leaks cluster in predictable places rather than spreading evenly.

So start at the furnace itself. The supply plenum and the return plenum are large, they carry the highest pressure, and they are usually assembled from several pieces.

Next, follow the trunk line. Every joint between sections is a candidate, and so is every takeoff where a branch leaves the trunk.

Then check the boot connections under floor registers. These move when people walk above them, and they loosen over the years.

Finally, look at anything a previous trade has cut through. Renovations and new wiring leave openings that nobody closed properly.

Location Why it leaks
Supply and return plenums Highest pressure, multi-piece assembly
Trunk joints Sections slip apart over time
Branch takeoffs Cut openings, often unsealed
Register boots Movement from foot traffic above
Renovation cuts Opened by other trades, rarely closed

Insulating, not just sealing

However, sealing is only half the job where the duct runs through cold space. The air still loses heat through bare metal.

Natural Resources Canada is direct about it. “Heating ducts running through unheated or cool basements and crawl spaces should be insulated.”

Moreover, the specification is given too. The guide says to “Cut RSI 2.1 (R-12) or more of batt or blanket insulation to size,” then wrap it and “secure with string, wire or approved tape.”

Still, one clearance rule comes with it. Do not wrap ducts “within 1.8 m (6 ft.) of a wood-fired furnace” unless the insulation is an approved non-combustible type.

Therefore seal first, then insulate. Wrapping over an unsealed joint simply hides it.

What sealing leaky ducts will not fix

Next, the honest limits. Duct sealing is not a cure for every comfort complaint.

Natural Resources Canada lists several faults side by side: “Undersized ductwork, leaking ducts, inadequate or poorly placed return air grilles and ducts can mean occupant discomfort and higher heating bills.”

Still, leakage is only one item on that list. Undersized ductwork and badly placed returns are separate problems, and sealing does nothing for either.

Cleaning is a different job again. The federal guide warns that “duct cleaning alone will not resolve balancing issues,” which is worth remembering before you book one.

Our notes on duct cleaning cover what that service actually does. Similarly, our guide to one room that is always cold works through the comfort side.

Large spiral metal ventilation ducts running along a ceiling
Balancing dampers come after the leaks are closed, not before.

Balancing comes after

Meanwhile, the order of operations matters. Adjusting dampers on a leaking system chases a moving target.

The federal guidance describes balancing as “Simple rebalancing of the system by either adjusting the dampers in a ducted system.” That works once the ducts hold the air they are given.

In practice the sequence runs: seal, insulate, then balance. Each step makes the next one measurable.

Airflow housekeeping belongs here too. Natural Resources Canada advises keeping “return-air grilles and warm-air vents clean and free of obstructions,” and changing filters “every three months or as they become loaded.”

Closing vents is not balancing, whatever it feels like. Our guide to closing air vents in unused rooms explains what that actually does to the system.

What sealing leaky ducts means around Belle Ewart

Belle Ewart sits on the Innisfil shore of Lake Simcoe, and the housing mix there runs from seasonal cottages to year round homes.

In practice, converted cottages are the interesting case. Ducts added during a conversion often run through crawl spaces that were never meant to be part of a heated building.

In those runs, sealing and insulating together pay back quickly. A bare duct in a vented crawl space loses heat the whole way along.

Besides, lakefront wind drives air leakage harder than an inland street does. Consequently the pressure difference across a leaky return is larger here than the same house would see elsewhere.

We serve Innisfil and the rest of Simcoe County, and converted cottage ductwork is familiar ground.

When to bring someone in

Finally, the point where this stops being a weekend job. Some of it genuinely is DIY, and some of it is not.

Of course, reachable joints in an open basement are fair game with foil tape or mastic. That work is low risk and visible.

However, ducts inside finished ceilings or walls are not accessible without damage. Likewise, a system that never balanced properly needs measurement rather than more tape.

Sizing is the deeper version of that problem. Our guide to what furnace size you need covers why an oversized unit makes duct faults worse.

If the house has never had a proper look, an annual maintenance visit is a sensible place to start.

Talk to Aire One Barrie

We seal and insulate ductwork to the federal guidance, and we measure before we adjust anything. We serve Innisfil and the rest of Simcoe County from our Barrie shop.

  • 24/7 emergency service, including weekends and holidays
  • Foil tape and mastic, never vinyl duct tape
  • Crawl space and cottage conversion ductwork
  • Bonded, factory trained and licensed technicians
Aire One Heating & Cooling Barrie · 176 Burton Ave, Barrie, ON · 705-733-1003

Frequently asked questions

What tape should I use for sealing leaky ducts?

Natural Resources Canada names aluminium foil duct tape, approved flexible plastic tape, or water based mastic. It specifically says not to use vinyl type duct tape, which is the grey cloth roll commonly sold under that name.

Do return ducts need sealing too?

Yes. The federal guidance covers plenums along with both supply and return ducts. A leaking return pulls cold basement air into the system, which the furnace then has to heat.

Should ducts be insulated as well as sealed?

Where they pass through unheated or cool basements and crawl spaces, yes. The guidance suggests RSI 2.1 (R-12) or more of batt or blanket insulation, secured with string, wire or approved tape.

Will sealing leaky ducts fix a cold room?

Sometimes, but not always. Undersized ductwork and poorly placed return grilles cause the same symptom, and sealing does nothing for either. Those need measurement rather than more tape.

Is duct cleaning the same thing?

No. Cleaning removes debris, while sealing closes air leaks. Natural Resources Canada notes that duct cleaning alone will not resolve balancing issues, so the two jobs answer different questions.

Henry Tabarsi, General Manager

Aire One has served Ontario since 1990, with Carrier Factory Authorized Dealer status and licensed technicians across Simcoe County.

705-733-1003 · 176 Burton Ave, Barrie, ON

Sources

  1. Natural Resources Canada, Keeping the Heat In, Chapter 9: Operating your house — sealing plenums and supply and return ducts, approved tapes and water based mastic, the warning against vinyl duct tape, insulating ducts in unheated spaces to RSI 2.1 (R-12), the wood-fired furnace clearance, rebalancing by adjusting dampers, the list of duct faults that cause discomfort, the limits of duct cleaning, and filter and grille housekeeping.
  2. Natural Resources Canada, Keeping the Heat In, Chapter 2: How your house works — air leakage accounting for roughly a quarter of heat loss, and uncontrolled airflow through the envelope as a major source of loss.