The decisions happen before the van arrives.
Sizing, venting and the licence question all belong to the quote stage. The install itself is mostly execution, and a good crew explains every step of it.
Google rating from 131 reviews, as of November 12, 2026
Licensed technicians
Quick answer
On furnace installation day the crew isolates the gas and power, removes the old unit, sets the new one, runs venting and the condensate drain, then commissions and tests it. Most replacements finish in a day. Only a TSSA registered contractor may carry out that work, since Ontario puts fuel appliances in their hands alone.
Key takeaways
- Firstly, sizing should come from a heat loss calculation, not a guess.
- Ontario lists authorised contractors publicly, so you can verify yours.
- A condensing furnace vents through plastic pipe, often out a side wall.
- It also makes water, which needs a drain or a pump.
- Above all, commissioning and a proper handover are part of the job.
Before furnace installation day arrives
First, the sizing. Natural Resources Canada is blunt here: a heat loss calculation should decide the furnace size.
Floor area alone “is not adequate in most cases,” and a number offered without a survey is “not much more than a ‘guesstimate.'”
Therefore ask to see that calculation before you sign. Our guide to what furnace size you need explains what it involves.
Secondly, verify who is coming. The Technical Standards and Safety Authority says “all Ontario contractors authorized by TSSA to perform fuel-related work are listed on the TSSA website.”
Moreover the regulator explains why that matters. “Fuels work can be dangerous, even deadly, if not performed by a professional,” and it cannot “validate their knowledge, competency and qualifications” otherwise.

What happens on furnace installation day
Secondly, the sequence itself. It rarely varies much.
The crew protects the route in first. Floors, stair treads and doorways take the traffic all day.
Then they isolate the gas and the electrical supply. Next the old furnace comes apart, and the plenum and venting disconnect with it.
After that they set and level the new unit. They also fabricate duct transitions to suit, because two models rarely share the same connections.
Meanwhile the gas line, the electrical connection and the thermostat wiring all land. Finally the venting and the condensate route finish the mechanical work.
| Stage | What is happening |
|---|---|
| Protection and isolation | Floors covered, gas and power shut off |
| Removal | Old unit, plenum and venting out |
| Setting | New furnace positioned and levelled |
| Connections | Duct transitions, gas, power, thermostat |
| Venting and drain | Intake, exhaust and condensate route |
| Commissioning | Gas pressure, combustion, airflow, safeties |
The venting is what changes about your house
Thirdly, the part homeowners notice afterwards. A condensing furnace does not use the old chimney.
Natural Resources Canada explains why. “A chimney is not needed because the flue gas temperature is so low that the gases are vented out of the house through an approved plastic pipe.”
Consequently new pipe appears outside. High-efficiency units generally vent “out a side wall” and draw combustion air from outdoors.
That means two new penetrations outside, usually paired. Besides, their location affects snow clearance every winter.
These units also produce water. The federal guide routes that condensate “to a floor drain or condensate pump.”
Furthermore, abandoning the chimney has knock-on effects. Where a water heater shared that flue, read about the chimney liner question before the work starts.
What a proper handover includes
Next, the finish. Commissioning is not paperwork, and it is where a good install separates itself.
Expect the crew to check gas pressure under load. Likewise they verify combustion, temperature rise across the heat exchanger and every safety control.
Then ask for the readings. A contractor who measured them can tell you what they were.
In addition, you should finish the day knowing four practical things. Where the filter goes, which way it faces, where the shutoffs are, and how the thermostat is set.
Finally, keep the documents together. Model and serial numbers matter later, and the efficiency rating should match what you bought.

What furnace installation day means around Moonstone
Moonstone sits in the higher ground of Oro-Medonte, and the snow belt treats it accordingly.
Side wall venting deserves real thought here. A termination placed low disappears under drifting snow by February.
Our guide to a furnace vent blocked by snow covers what happens when it does. Consequently ask where the terminations will sit while the quote is still open.
Moreover, many properties here run long driveways and older service. Confirm the electrical supply suits the new equipment before the day arrives.
Red flags worth acting on
However, some signals should stop the job rather than slow it. Treat them seriously.
A quote with no heat loss calculation is the first. The federal guide calls an unsurveyed number a guesstimate, and that is your money at stake.
Next, a contractor you cannot find on the public list. TSSA identifies “inadequate installation and poor maintenance” among the major contributing factors to fuel-related risk in homes.
Cash-only pricing well below everyone else is another. The regulator notes that uncertified workers “charge less for labour” and avoid its compliance audits.
Finally, a crew that leaves without walking you through the system has not finished. Ask for the handover before anyone drives away.
Talk to Aire One Barrie
We calculate heat loss before quoting, and we hand over the commissioning readings at the end. We serve Oro-Medonte and the rest of Simcoe County from our Barrie shop.
- 24/7 emergency service, including weekends and holidays
- We calculate heat loss before quoting any furnace
- Vent terminations planned around snow loading
- Bonded, factory trained and licensed technicians
Frequently asked questions
How long does furnace installation day take?
Most straightforward replacements finish within a day. A changeover that also needs new venting, a condensate route or ductwork modifications can run longer, so ask for the expected schedule when you accept the quote.
Do I need to be home?
Someone should be there at the start and at the handover. The start confirms access and placement, while the handover covers the filter, the shutoffs and the thermostat settings.
Will there be new pipes on the outside wall?
Usually yes with a condensing furnace. Natural Resources Canada explains that the flue gas is cool enough to vent through approved plastic pipe, and that high-efficiency units generally vent out a side wall.
How do I check the contractor may legally do the work?
The Technical Standards and Safety Authority publishes every Ontario contractor it authorises for fuel-related work on its website. Ontario places fuel appliances in the hands of TSSA-registered contractors only.
What should I get at the end of the day?
A walkthrough of the system, the commissioning readings, and the documents with model and serial numbers. Check that the efficiency rating on the unit matches what the quote described.
Aire One has served Ontario since 1990, with Carrier Factory Authorized Dealer status and licensed technicians across Simcoe County.
705-733-1003 · 176 Burton Ave, Barrie, ON
Sources
- Natural Resources Canada, Heating with Gas — sizing by heat loss calculation, floor area alone being inadequate, the guesstimate warning, plastic pipe and side wall venting, outdoor combustion air, and condensate piped to a floor drain or pump.
- Technical Standards and Safety Authority, TSSA Cautions Ontario Homeowners Against Hiring Fraudulent Fuels Workers — fuel appliances maintained by TSSA-registered contractors, the public listing of authorised contractors, the dangers of uncertified work, and inadequate installation as a contributing factor to fuel-related risk.










